r-software
Differences
This shows you the differences between two versions of the page.
Both sides previous revisionPrevious revisionNext revision | Previous revisionNext revisionBoth sides next revision | ||
r-software [2017/02/06 13:10] – joguya | r-software [2019/08/08 13:27] – aorth | ||
---|---|---|---|
Line 4: | Line 4: | ||
===== Information ===== | ===== Information ===== | ||
- | * Latest version: 3.3.2 | + | * Version: 3.5.3 |
* Added: February, 2015 | * Added: February, 2015 | ||
- | * Updated: | + | * Updated: |
- | * Link: http:// | + | * Link: https:// |
===== Usage ===== | ===== Usage ===== | ||
- | === See versions of R which are available | + | See versions of R that are available: |
- | < | + | < |
- | ===== Installation ====== | + | Load one version into your environment and run it: |
- | Notes from the sysadmin during installation: | + | < |
- | - install zlib/ | + | $ R</code> |
- | $ cd /tmp | + | |
- | $ wget -qO- " | + | |
- | $ sudo mkdir -p / | + | |
- | $ sudo chown -R joguya: | + | |
- | $ scl enable devtoolset-2 bash | + | |
- | $ cd zlib-1.2.8/ | + | |
- | $ ./configure --prefix=/ | + | |
- | $ make -j4 | + | |
- | $ make install | + | |
- | $ export LD_LIBRARY_PATH=$LD_LIBRARY_PATH:/ | + | |
- | - install bzip2/ | + | Here is a good resource on [[https://www.osc.edu/resources/getting_started/howto/howto_install_local_r_packages|installing |
- | $ wget -qO- http://www.bzip.org/1.0.6/bzip2-1.0.6.tar.gz | tar xzv | + | |
- | $ cd bzip2-1.0.6/ | + | |
- | $ sudo mkdir -p /export/ | + | |
- | $ sudo chown -R joguya: | + | |
- | $ make -f Makefile-libbz2_so | + | |
- | $ make clean | + | |
- | $ make | + | |
- | $ make -n install PREFIX=/ | + | |
- | $ make install PREFIX=/ | + | |
- | $ export PATH=/ | + | |
- | - install xz instead of liblzma | + | ===== Installation ====== |
- | $ wget -qO- http:// | + | Notes from the sysadmin during installation: |
- | $ cd xz-5.2.2/ | + | |
- | $ sudo mkdir -p / | + | |
- | $ sudo chown -R joguya: | + | |
- | $ ./configure --prefix=/ | + | |
- | $ make -j4 | + | |
- | $ make install | + | |
- | $ export PATH=/ | + | |
- | - install pcre/8.35 | + | < |
- | $ wget -qO- http://downloads.sourceforge.net/pcre/pcre-8.35.tar.bz2 | tar xjv | + | $ wget https://cran.r-project.org/src/base/R-3/R-3.5.3.tar.gz |
- | $ cd pcre-8.35/ | + | $ tar xf R-3.5.3.tar.gz |
- | $ sudo mkdir -p / | + | $ cd R-3.5.3 |
- | $ sudo chown -R joguya: | + | $ sudo yum install gcc-gfortran gcc-c++ libX11-devel libXaw-devel bzip2-devel libcurl-devel xz-devel readline-devel |
- | $ ./configure --prefix=/ | + | $ ./ |
$ make -j4 | $ make -j4 | ||
- | $ make check | + | $ sudo mkdir -p / |
+ | $ sudo chown aorth:aorth / | ||
$ make install | $ make install | ||
- | $ export PATH=/ | + | $ sudo chown -R root:root / |
- | - install libcurl/ | + | Note to future Alan: don't remove '' |
- | $ wget -qO- https:// | + | |
- | $ cd curl-7.47.1 | + | |
- | $ sudo mkdir -p / | + | |
- | $ sudo chown -R joguya: | + | |
- | $ ./configure --prefix=/ | + | |
- | $ ./configure --enable-ipv6 --enable-ldap --enable-ldaps --with-nghttp2 --prefix=/ | + | |
- | $ export PATH=/ | + | |
- | + | ||
- | - install | + | |
- | $ cd /tmp/ | + | |
- | $ wget -qO- https:// | + | |
- | $ cd R-3.3.2/ | + | |
- | $ scl enable devtoolset-2 bash | + | |
- | $ sudo mkdir / | + | |
- | $ sudo chown -R joguya: | + | |
- | $ ./configure --enable-R-static-lib --prefix=/ | + | |
- | $ make -j4 | + | |
- | $ make install | + | |
- | $ sudo chown -R root:root / | + | |
- | </ | + |
r-software.txt · Last modified: 2023/07/12 06:39 by aorth